Genemco Sells Used Plate Heat Exchanger/Evaporator, Vacuum Pan Evaporator, Lo-Temp Evaporators and Vacuumizer Tanks by APV, Mojonnier, Cherry-Burrell 
 Genemco Offers Used Used Plate Heat Exchanger/Evaporator, Vacuum Pan Evaporator, Lo-Temp Evaporators and Vacuumizer Tanks 

Click On Picture

APV Essence Recovery System

APV Essence Recovery System
Mfg: APV Model:
Stock No: CMCS01D Serial No:
APV Essence Recovery System. Previously used with a 3-effect 5-stage evaporation system removing 30,000 lbs per hour of water from a food product at a major USA food processing plant.

Click On Picture

TVR for APV FF / RFF Evaporation System

TVR for APV FF / RFF Evaporation System
Mfg: Croll Reynolds Co. Model:
Stock No: CMCS01E Serial No:
Used Croll-Reynolds TVR for FF / RFF Evaporation System. Thermocompressor. Model: M16-T. Serial: 61972. Stage: T. Press.: 90 PSIG. Westfield, NJ. Previously used with an APV 3-effect 5-stage evaporation system removing 30,000 lbs per hour of water from a food product at a major USA food processing plant. Includes the TVR part only. Approx. dimensions: 10 ft. L x 2 ft. W x 2 ft. H.

Click On Picture

Stainless Steel Shell and Tube Pre-Heater and Condenser

Stainless Steel Shell and Tube Pre-Heater and Condenser
Mfg: Merrick Mechanical Model:
Stock No: HDDF148J Serial No: 225
Stainless Shell and Tube Heat Exchangers, previously used with an APV Evaporation system. Condensate Units. Merrick Mechanical Shell and Tube Condenser. S/N: 225. Nat'l Bd: 130. Number of tubes: 256. Heat transfer surface area: approx. 332 sq. ft. Number of passes: 3. MAWP shell side: 100 psi @ 160F. MDMT shell side: -20 F @ 100 psi. MAWP tube side: 75 psi @ 160 F. MDMT tube side: -20 F @ 75 psi. Inlets: (1) 5 in. dia. ANSI 150 class flanged port, (1) 4 in. dia. port. Outlets: (1) 5 in. dia. ANSI 150 class flanged port, (1) 18 in. dia. ANSI class 150 flanged port. Stainless Steel Shell and Tube Pre-Heater. Number of tubes: 40. Heat transfer surface area: approx. 125 sq. ft. Number of passes: 6. Inlets/Outlets: (2) 2 in. ACME fitting, (1) 2 in. FNPT, (1) FNPT, (2) 1 in. ACME fittings, (1) 2-1/2 in. flange port (flange dia. 6 in). Skid overall dimensions: 13 ft. L x 44 in. W x 99 in. H.

Click here for more information (178.9 KB)

Click On Picture

APV Essence Recovery System

APV Essence Recovery System
Mfg: APV Model:
Stock No: HGPS1028B Serial No:
APV Essence Recovery System. Includes APV vertical column with JD Cousins U-tube coil, two Hebeler Corporation essence storage tanks, balance tank, centrifugal pumps, Rosemount flowmeter, pneumatic valves, etc. Column dimensions: 6 ft. 4 in. L x 2 ft. 3 in. W x 19 ft. H. Overall dimensions: 9 ft. L x 6 ft. 6 in. W x 7 ft. H

Click here for more information (848.2 KB)

Click On Picture

APV Bundel Cavitator For Essence Recovery

APV Bundel Cavitator For Essence Recovery
Mfg: APV Model: 1448-U
Stock No: HGPS1028.26 Serial No: 594-13
APV Crepaco Bundel Cavitator For Essence Recovery. Model: 1448-U. Serial: 594-13. Vertical orientation. Includes control box. Tube ratings: MAWP: 150 PSI / FL at 300F; MDMT: -20F at 150 PSI / FV. Year built: 1994.

Click here for more information (162.8 KB)

Click On Picture

Essence Recovery Skid With Storage Tanks and Pumps

Essence Recovery Skid With Storage Tanks and Pumps
Mfg: Hebeler Corp. Model:
Stock No: HGPS1043.3a Serial No: H2109
Essence Recovery Skid With Storage Tanks and Pumps. (2) Hebeler Essence Storage Tanks. S/N: H2109. MAWP: 60 PSIG at 100F. MDMT: -20F at 60 PSIG. Year: 1994. Natl Bd. 6056. Hebeler Corporation Tonawanda NY USA. Surge Tank and (3) Assorted Pumps.

Click here for more information (205.4 KB)

Click On Picture

APV Ceramic Saddle Distillation Essence Recovery System

APV Ceramic Saddle Distillation Essence Recovery System
Mfg: APV Model:
Stock No: 35.D01 Serial No:
APV Ceramic Saddle Distillation Essence Recovery System. Distillation column dimensions: 2 ft. 3 in. dia. x 45 ft. 6 in. H. (4) Whitlock Hi-Transfer Shell and Tube Heat Exchangers. Inlets: (1) 2 in. dia. flanged port, (1) 3 in. dia. flanged port, (1) 4 in. dia. flanged port, (1) 10 in. dia. flanged port. Outlets: (1) 8 in. dia. flanged port. Overall dimensions: 4 ft. L x 3 ft. 6 in. W x 45 ft. 6 in. H. Shell and Tube Heat Exchanger Skid. Primary Shell and Tube Heat Exchanger. Tube material: 316 stainless steel. Number of passes: 1. Number of tubes: 89. Tube dimensions: 3/4 in. dia. x 6 ft. L. Heat transfer surface area: approx. 104.8 sq. ft. Inlets: (1) 8 in. dia. ANSI 150lb. flanged port (product), (1) 4 in. dia. ANSI 150lb. flanged port (media). Outlets: (1) 2 in. dia. condensate port, (1) 4 in. dia. ANSI 150lb. flanged port (media), (1) 8 in. dia. ANSI 150lb. flanged port (product). Secondary Shell and Tube Heat Exchanger. Tube material: 316 stainless steel. Number of passes: 1. Number of tubes: 123. Tube dimensions: 3/4 in. dia. x 8 ft. L. Heat transfer surface area: approx. 193.2 sq. ft. Inlets: (1) 8 in. dia. ANSI 150lb. flanged port (product), (1) 8 in. dia. ANSI 150lb. flanged port (media). Outlets: (2) 2 in. dia. ACME fittings (product), (1) 8 in. dia. ANSI 150lb. flanged port (media). Overall dimensions (heat exchanger skid): 9 ft. 9 in. L x 5 ft. 1 in. W x 3 ft. 11 in. H.

Click here for more information (721.0 KB)

Click On Picture

Stainless Steel Essence Recovery System - 65.9 sq. ft.

Stainless Steel Essence Recovery System - 65.9 sq. ft.
Mfg: Not Specified Model:
Stock No: CCFP526. Serial No:
Stainless Steel Essence Recovery System. Re-boil u-tube capacity: 328 lbs/hr. (1st) Whitlock Hi-Transfer shell and tube heat exchanger/condenser: (222) 5/16 in. dia. x 36 in. L tubes and 65.9 sq. ft. of surface area. (2nd) Whitlock Hi-Transfer shell and tube heat exchanger: (84) 5/16 in. dia. x 36 in. L tubes and 24.7 sq. ft. of surface area. Essence cooler: (12) 1-3/8 in. dia. x 15 ft. L tubes. Essence column dimensions: 11-1/2 in. inner dia x 17 ft. H. System is used to "strip" feed juices of their flavor by evaporation and to "concentrate" these esters in a distillation column. Overall dimensions: 6 ft. 1 in. L x 4 ft. 1 in. W x 17 ft. 4 in. H.(HB1).

Click here for drawing (119.3 KB)
Click here for more information (578.3 KB)
Click here for general application drawing (6,322.2 KB)

Click On Picture

Stainless Steel Vertical Tank - 500 gallons

Stainless Steel Vertical Tank - 500 gallons
Mfg: Not Specified Model:
Stock No: TMCB280B Serial No:
Stainless Steel Vertical Tank. Inside dimensions: 40 in. ID x 8 ft. high sidewall. Approximate capacity: 500 gallons. Port: 3 in. flange at top, 2 in. tri-clamp at lower side, 3 in. bevel seat at bottom. Overall dimensions: 4 ft. x 4 ft. x 13 ft high.

Click On Picture

Groen Slurry Concentrator

Groen Slurry Concentrator
Mfg: Groen Model:
Stock No: SGMPM089.125a Serial No:
Groen Slurry Concentrator. (H)

Click here for more information (235.0 KB)

Click On Picture

Stainless Steel Centrifugal Deaerator Skid

Stainless Steel Centrifugal Deaerator Skid
Mfg: Not Specified Model:
Stock No: OI244. Serial No:
Stainless Steel Centrifugal Deaerator Skid. Maximum tank volume: 8 gal. Mixing head diameter: 7-1/2 in. Mixer Motor, 3/4 hp, 220 V, 2.25 amps, 60 Hz, 3 phase. Fryma-Maschinen Progressing Cavity Positive Displacement Pump, Model: NU-15A. Motor, 1/2 hp, 1100 rpm, 380 V, 1.4 amps, 60 Hz, 3 phase. Siemen and Hinsch Vacuum Pump with Motor, Model: LEMA 25 A7 GA1 7C0, S/N: D-3126498. Inlets: (1) 3/8 in. dia. vacuum port, (1) 1/2 in. dia. MPT, (1) 1 in. dia. flanged port. Outlets: (1) 1-1/2 in. dia. port. Overall dimensions: 54 in. L x 22 in. W x 52 in. H.

Click here for more information (300.4 KB)

Click On Picture

Concentrator Plates - 89 in.

Concentrator Plates - 89 in.
Mfg: Not Specified Model:
Stock No: RTTA560.42a Serial No:
Concentrator Plates. 89 in. x 37 in. Approximately 52 plates.(ACN8).

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA561.42a Serial No:
Concentrator Plates. 89 in. x 37 in. Approximately 30 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA562.42a Serial No:
Concentrator Plates. 89 in. x 37 in. Approximately 150 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA563.42a Serial No:
Concentrator Plates. 89 in. x 37 in. Approximately 150 plates.

Click On Picture

Concentrator Plates - 54 in.

Concentrator Plates - 54 in.
Mfg: Not Specified Model:
Stock No: RTTA564.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 120 plates. (ACN5a)

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA565.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 110 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA566.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 110 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA567.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 90 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA568.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 120 plates.

Click On Picture

Concentrator Plates

Concentrator Plates
Mfg: Not Specified Model:
Stock No: RTTA569.16 Serial No:
Concentrator Plates. 54 in. x 30 in. Approximately 180 plates.

Click On Picture

Alfa Laval Stainless Steel Separator - 80 Gallons

Alfa Laval Stainless Steel Separator - 80 Gallons
Mfg: Alfa Laval Model: DD-750-LC
Stock No: SSFF1013.14 Serial No: 32142-1161
Alfa Laval Stainless Steel Separator. Model: DD-750-LC. Approximate capacity: 80 gallons. Inside dimensions: 29 in. dia. x 29 in. H (straight wall). Features side, top access ladder and a 4 in. diameter sight glass. Inlet/outlet(s): (2) 1 in., 1-3/4 in., 2 in. (2) 3 in. threaded. Overall dimensions: 2 ft. 5 in. L x 3 ft. W x 11 ft. 8 in. H.

Click here for more information (99.0 KB)

Click On Picture

Alfa Laval Stainless Steel Separator  80 Gallons

Alfa Laval Stainless Steel Separator 80 Gallons
Mfg: Alfa Laval Model: DD 750
Stock No: SSFF1015.14 Serial No: 3242-1247
Alfa Laval Stainless Steel Separator. Model: DD 750. Approximate capacity: 80 gallons. Inside dimensions: 29 in. dia. x 29 in. H (straight wall). Features side, top access ladder and a 4 in. diameter sight glass. Inlet/outlet(s): 1 in., (4) 1-1/2 in., 2 in. (2) 3 in. threaded. Overall dimensions: 2 ft. 5 in. L x 2 ft. 11 in. W x 13 ft. 3 in. H.

Click here for more information (126.8 KB)

Click On Picture

Shell and Tube Heat Exchanger Skid - 239 sq. ft.

Shell and Tube Heat Exchanger Skid - 239 sq. ft.
Mfg: Not Specified Model:
Stock No: 35B.D01a Serial No:
Shell and Tube Heat Exchanger Skid. Primary Shell and Tube Heat Exchanger. Tube material: 316 stainless steel. Number of passes: 1. Number of tubes: 87. Tube dimensions: 3/4 in. dia. x 6 ft. L. Heat transfer surface area: approx. 102.4 sq. ft. Inlets: (1) 8 in. dia. ANSI 150lb. flanged port (product), (1) 4 in. dia. ANSI 150lb. flanged port (media). Outlets: (1) 2 in. dia. condensate port, (1) 4 in. dia. ANSI 150lb. flanged port (media), (1) 8 in. dia. ANSI 150lb. flanged port (product). Secondary Shell and Tube Heat Exchanger. Tube material: 316 stainless steel. Number of passes: 1. Number of tubes: 87. Tube dimensions: 3/4 in. dia. x 8 ft. L. Heat transfer surface area: approx. 136.6 sq. ft. Inlets: (1) 8 in. dia. ANSI 150lb. flanged port (product), (1) 8 in. dia. ANSI 150lb. flanged port (media). Outlets: (2) 2 in. dia. ACME fittings (product), (1) 8 in. dia. ANSI 150lb. flanged port (media). Overall dimensions: 9 ft. 9 in. L x 5 ft. 1 in. W x 3 ft. 11 in. H.

Click here for more information (709.8 KB)

Click On Picture

Alloy Products Corp. Pharmaceutical/Hygienic Pressure Vessel

Alloy Products Corp. Pharmaceutical/Hygienic Pressure Vessel
Mfg: Alloy Products Model:
Stock No: TACJ0316.1 Serial No: 52518-001
Alloy Products Corp. Pharmaceutical/Hygienic Pressure Vessel. S/N: 52518-001. Date made: 1990. 130 PSI Max. W.P. 100 ˚F. Min. Temp. -20˚F 130 PSI. 15 Gallon pressure vessel. Inlets/outlets: (4) in. FNPT. Inside dimensions: 1 ft. dia. x 2 ft. 2 in. straight wall. Overall dimensions: 1 ft. L x 1 ft. W x 2 ft. 11 in. H.

Click here for more information (237.8 KB)

Click On Picture

Paul Mueller Dedert Dimpled Jacketed Vacuum Tank - 4,000 Gallons

Paul Mueller Dedert Dimpled Jacketed Vacuum Tank - 4,000 Gallons
Mfg: Paul Mueller Co. Model:
Stock No: SABE095.15 Serial No: 120908
Paul Mueller Dedert Dimpled Jacketed Tank. Approximate capacity: 4000 gallons. Constructed of 316 stainless steel. Inside dimensions: 72 in. dia x 20 ft. Long. Vessel MAWP @ 275F: 0 psi. / Vacuum 29.92 HG. Heat transfer surface MAWP @ 275F: 30 psi. Tank features an 18 in. dia. manway and a 6 in. dia. sight glass. Overall dimensions: 6 ft. 4 in. L x 6 ft. 4 in W x 28 ft. 6 in. H.

Click for a Video walk around of this tank

Click here for more information (431.2 KB)

Click On Picture

Westfalia-Graham Two Stage Flash Cooler

Westfalia-Graham Two Stage Flash Cooler
Mfg: Westfalia Model: Ejector
Stock No: ENDX672A Serial No: 1079 1
Westfalia Industries Inc. Two Stage Flash Cooler. Graham Mfg. (Canada) LTD model: Ejector, serial 1079 1, motive pressure: 100 PSI. Material: 304 stainless steel. This flash cooler was originally part of a system that was used to concentrate dairy products to high solids. Inlets/Outlets: (1) 8 in. dia. flanged port on side, (1) 6 in. dia. flanged port on top, (3) 3 in. dia. s-line connections, (3) 2 1/2 in. dia. s-line connections. Overall dimensions: 4 ft. 6 in. L x 4 ft. 1 in. W x 16 ft. H. (ND)

Click here for more information (151.2 KB)

Click On Picture

2003 Wittemann Company MW Deaerator

2003 Wittemann Company MW Deaerator
Mfg: Witteman Company Model: A0003173-001
Stock No: TMCB302.1a Serial No: 52549-1-1
2003 Wittemann MW Deaerator. Model: A0003173-001. Tank capacity: 100 gallons. Tank straight wall height: 2 ft. 6 in. Tank diameter: 2 ft. 7 in. Top Flange: 13 in. I.D.,17 in. O.D. Ports: (2) in. FNPT, (2) 1 in. FNPT, (2) in. FNPT with 19 in. sight glass attached , in. FNPT with pressure gauge attached, in. FNPT with thermometer attached. Outlet pipe with tee to 1 in. MNPT and 6 in. flange (3 in. diameter opening). Tank overall dimensions: 3 ft. 6 in. L x 2 ft 7 in. W x 4 ft. 2 in. H. Stainless steel centrifugal pump: Pump motor: Baldor 2 HP, 208-230/460 V, 6.2-5.8/2.9 A, 3450 R.P.M., 60 Hz, 3 phase. 2 in. centrifugal pump. Inlet: 6 in. Flange with 3 in. I.D. Outlet: 5 in. Flange with 2 in. I.D. Pump overall dimensions: 19 in. L x 9 in. W x 12 in. H. Tube: Tube straight wall height: 10 ft. in. Tube diameter: 1 ft. 5 in. Tube top flange: 13 in. I.D., 17 in. O.D. Bottom flange: 12 in. I.D., 17 in. O.D. Ports: Side inspection port: 8 in. I.D., 10 in. O.D. Top port: (2) 1 in. FNPT with 5 in. Flange currently attached. Wire mesh on bottom of tube is constructed of 1/8 in. stainless wire with in. to n. opening. Overall tube dimensions: 26 in. L x 21 in. W x 10 ft. in. H. Control box: Overall Dimensions: 1 ft. 1 in. L x 6 in. W x 1 ft. 1 in. H. Overall dimensions: 3 ft. 6 in. L x 3 ft. 4 in. W x 14 ft. 2 in. H.

Click here for more information (925.7 KB)

Click On Picture

1994 Cozzini Vacuum Chamber Processor with Pump  185 Gallons

1994 Cozzini Vacuum Chamber Processor with Pump 185 Gallons
Mfg: Cozzini Model: VP-700
Stock No: KAAM0418.13 Serial No: 0128
1994 Cozzini Vacuum Chamber Processor with Pump. Model: VP-700. Approximate throughput capacity: 11,000 lbs. per hour. Approximate vacuum chamber capacity: 185 gallons. Tri-Clover positive displacement pump. Reliance electric motor, 7-1/2 hp, 1755 rpm, 230/460 V, 27/13.5 amps, 60 Hz, 3 phase. Reliance electric variable speed module, rpm (min/max): 450/45. Typically used in the processing of meat emulsions such as wieners and hot dogs, the Cozzini VP-700 removes air from the product prior to packaging, thus ensuring product uniformity and increasing shelf life. Inlets: (1) 3/8 in. dia. FNPT, (1) 3/4 in. dia. FNPT ball valve, (1) 2 in. dia. FNPT, (1) 2 in. dia. S-line fitting, (2) 4 in. dia. S-line fitting. Outlets: (1) 9 in. L x 2-1/2 in. W discharge. Overall dimensions: 7 ft. 8 in. L x 4 ft. 8 in. W x 7 ft. 4 in. H.(ACN400).

Click here for more information (848.9 KB)

Click On Picture

Enterprise Co. Mounted Vacuum Deaeration Chamber Skid

Enterprise Co. Mounted Vacuum Deaeration Chamber Skid
Mfg: Enterprise Co. Model: J2805.987
Stock No: END9741.218a Serial No: E100133
Enterprise Co. Mounted Vacuum Deaeration Chamber Skid. Model J2805.987. S/N E100133. 230-460 volts, 60 Hz, 3 phase. Stainless steel Tri Clover manifold. Has a Hoffman Control Panel. Cat # A-42HS3112SSLP Model # VCP-623, The overall measurements 14 in. W, 35 in. L, 44 in. H. 1 vacuum pump (Model & Serial N/A) with Baldor Motor, Cat # - CWDM3555T, 2 hp, 3,450 rpm, 60 Hz, 3 phase, 208-230/460 volts, 5.6 -5.2/2.6 amps, Inlet and Outlet 1-1/2 in. 1 Ampco Pump, Model 2-1/2 x 2 MC2, S/N CC-15477-1-1, IMP 6.500 with Baldor Motor, Cat # JMWDM3558T, Serial # F798, 2 hp, 60 Hz, 1,725 rpm, 208-230/460 volts, 6.5-6.2/3.1 amps. Inlet 2 in. and outlet 2-1/2 in. Deaeration Chamber has three sight glasses and a volume including cone of 25,786 cubic in. Overall dimensions 43 in. L x 76 in. W x 120 in. H.

Click here for more information (372.0 KB)

Click On Picture

Mojonnier Stainless Steel Vacuum Pan Evaporator-1,300 Gallon

Mojonnier Stainless Steel Vacuum Pan Evaporator-1,300 Gallon
Mfg: Mojonnier Model:
Stock No: HDBA120.14 Serial No:
Mojonnier Stainless Steel Vacuum Pan Evaporator- 1,300 Gallons. Size: 48 399. 316 stainless steel. (2) manways: 16 in. dia. (1) Sight glass: 4-1/2 in. dia. Inlets/outlets: (1) 1/2 in. dia. female ferrule, (1) 1 in. dia. male ferrule with hex nut, (1) 1 in. dia. pipe, (1) 1-1/2 in. dia. male ferrule with hex nut, (1) 1-1/2 in. dia. threaded fitting, (1) 2 in. dia. threaded fitting, (1) 2 in. dia. male ferrule with hex nut, (5) 2 in. dia. FPT, (1) 5 in. dia. with a 10 in. dia. flange and (8) 3/4 in. dia. attachment holes. Overall dimensions: 56 in. L x 54 in. W x 17 ft. 4 in. H.

Click here to see a video of the equipment

Click here for drawings (1,899.0 KB)
Click here for more information (534.5 KB)

Click On Picture

Mojonnier Lo Temp Evaporator

Mojonnier Lo Temp Evaporator
Mfg: Mojonnier Model: LTFL
Stock No: 55.233 Serial No: 44
Mojonnier Lo-Temp Evaporator. Model: LTFL. S/N: 44. ITT Jabsco Rotary Pump, Model: 903-0024, S/N: 12061-0000. Century Electric Motor, 1/4 hp, 1735 rpm, 220 V, 85 amps, 60 Hz, 3 phase. Pump, Model D791. Marathon Electric Motor, 3 hp,1725 rpm, 208-230/440 V, 60 Hz, 3 phase. Cenco Pressuvac 4 Pump with a Century Electric Motor, 1/4 hp, 1735 rpm, 220 V, 85 amps, 60 Hz, 3 phase. Inlets: (2) 1/2 in. dia. infeed (product), (1) 1/4 in. dia. FNPT (steam). Outlets: (1) 1/2 in. dia. port (condensate), (1) 3/4 in. dia. port (vapor), (2) 1-1/2 in. dia. ports (product). Overall dimensions: 58 in. L x 36 in. W x 84 in. H.

Click here for more information (667.5 KB)

Click On Picture

Groen Vacuum Flash Chamber System

Groen Vacuum Flash Chamber System
Mfg: Groen Model: Flash Chamber
Stock No: G116-BC. Serial No: 83196
Groen Vacuum System. Previously used as a deodorizer. Model: Flash Chamber. S/N: 83196. MAWP: 50 psi. Groen Vertical Separator- 20 Gallon, inside straight-wall dimensions: 1 ft. 5 in. dia. x 1 ft. 9 in. H, CIP sprayball-equipped. Inlets: (1) 2 in. dia. S-line fitting. Outlets: (1) 1-1/2 in. dia. S-line fittings. Media: (1) 1 in. dia. S-line fittings. Ametek shell and tube condenser. G&H positive displacement recirculation pump. 2 HP vacuum pump. Overall dimensions: 6 ft. 6 in. L x 2 ft. 6-1/2 in. W. 8 ft. 3 in. H.

Click here for more information (1,010.1 KB)

Click On Picture

Rossi & Catelli Vacuum Chamber-25 Gallon

Rossi & Catelli Vacuum Chamber-25 Gallon
Mfg: Rossi & Catelli Model:
Stock No: 57a.MFM3237.5 Serial No: 2483
Rossi & Catelli Vacuum Chamber-25 Gallon. S/N: 2483. MAWP tube side: 42 psi. MDMT tube side: 289.3F. HT tube side: 71 psi. MAWP shell side: 0 psi. MDMT shell side: 104 F. HT shell side: 0 psi. Equipped with (2) pneumatic valves. Inlets: (1) 1 in. dia. with 4-1/2 in. dia. flange and (4) 1/2 in. dia. attachment holes at a center-to-center distance of 4 in., (1) 1-1/2 in. dia. male ferrule, (2) 2-1/2 in. dia. with 4-1/2 in. dia. flanges and (4)1/2 in. dia. attachment holes at a center-to-center distance of 4 in., each, (1) 4 in. dia. with an 8-1/2 in. dia. flange and (8) 3/4 in. dia. attachment holes at a center-to-center distance of 7 in. Outlets: (1) 2 in. dia. female ferrule. Overall dimensions: 48 in. L x 41 in. W x 11 ft. 4 in. H.

Click here for more information (327.3 KB)

Click On Picture

2004 Niro Inc. Vacuum Chamber Skid

2004 Niro Inc. Vacuum Chamber Skid
Mfg: Niro Model:
Stock No: DLEC047.22 Serial No: JS2588
2004 Niro Inc. Vacuum Chamber Skid. National Bd No. 5569. S/N: JS2588. Equipment No. VLS-9532. Drawing No. JS-2588. ESP Control Panel. Project No. 3544. S/N: 0947. Drawing No. 03312132-13G1-532. Power supply: 120 V, 60 Hz, single phase. Overall dimensions: 7 ft. L x 3 ft. 8 in. W x 7 ft. 7 in. H.

Click here for more information (779.3 KB)

Click On Picture

DeLaval Stainless Steel Vacuumizer - 115 gallons

DeLaval Stainless Steel Vacuumizer - 115 gallons
Mfg: DeLaval Model: 650
Stock No: G-510 Serial No:
DeLaval Stainless Steel Vacuumizer for HTST System. Model: 650. 35,000 lb/hr capacity. Approximate Volume: 115 gallons. (3) 1 ft. 11 in. perforated plates with (4) 3-1/4 in. holes. (2) 1 ft. 5-3/4 in. solid plates. (1) 1 ft. 6 in. dia. floater. (2) 5-5/8 in. dia. glass windows. (1) 3 in. S-line inlet. (1) 2-1/2 in. S-line inlet. (1) 3 in. S-line outlet. Inside dimensions: 2 ft. 1 in. dia. x 4 ft. 7-1/2 in. straight wall. Overall dimensions: 3 ft. 1-1/2 in. L x 2 ft. 7-1/2 in. W x 7 ft. 3 in. H.

Click here for more information (493.0 KB)

Click On Picture

Vacu-Therm - 50 Gallon

Vacu-Therm - 50 Gallon
Mfg: Not Specified Model:
Stock No: 29.GO890101 Serial No:
Stainless steel 50 gallon Vacu-Therm tank with (2) 5 in. sight glasses, 1-1/2 in. inlet, 2 in. inlet, 2 in. outlet.

Click On Picture

Cherry Burrell Aro-Vac Flavorizer- 285 Gallon

Cherry Burrell Aro-Vac Flavorizer- 285 Gallon
Mfg: Cherry-Burrell Model: AVC-SH
Stock No: RWAF329.7 Serial No: 824
Cherry Burrell Aro-Vac Flavorizer- 285 Gallon. Model: AVC-SH. S/N: 824. Inside straight-wall dimensions: 3 ft. dia. x 5 ft. 5 in. H. Manway diameter: 1 ft. 4 in. Jacketed tube dimensions: 9 in. dia. x 1 ft. 8 in. H. Inlets: (1) 1-1/2 in. dia. sprayball port, (1) 3/8 in. dia. NPT media port. Outlets: (1) 3/8 in. dia. media discharge, (1) 2 in. dia. S-line suction port, (1) 4 in. dia. S-line drain port. Overall dimensions: 3 ft. 11 in. L x 3 ft. 10 in. W x 10 ft. 4 in. H.(HB1).

Click here for more information (246.6 KB)

Click On Picture

Crepaco Deaerator Tank

Crepaco Deaerator Tank
Mfg: Crepaco Model: 2100
Stock No: HE71-1634.0 Serial No: A37784
Crepaco deaerator tank, Model 2100, S/N A37784 with 4 in. clamp connection.

Click On Picture

Vacuumizer Tank-70 Gallon

Vacuumizer Tank-70 Gallon
Mfg: Not Specified Model:
Stock No: 134 Serial No:
Vacuumizer Tank- 70 Gallon. Stainless steel. Inlets: (2) 3 in., (2) 4 in., (1) 2-1/2 in. Outlets: (2) 3 in., (2) 2-1/2 in., (1) 2 in. Inside dimensions: 23-1/2 in. dia x 41 in. H. Legs: (4) 37 in. H. Overall dimensions: 72 in. L x 40 in. W x 83 in. H.

Click here for more information (222.9 KB)

Click On Picture

Vapor Chamber Stainless Steel

Vapor Chamber Stainless Steel
Mfg: Not Specified Model:
Stock No: 277 Serial No:
Vapor Chamber Stainless Steel. Manway: 15 in. dia. CIP spray ball. Inlet: 20 in. dia flanged. Outlets: (4) 3-1/2 in. Overall dimensions: 16 ft. L x 5.3 ft. W.

Click here for more information (184.2 KB)

Click On Picture

Stainless Steel Vapor Chamber-575 Gallon

Stainless Steel Vapor Chamber-575 Gallon
Mfg: Not Specified Model:
Stock No: 278 Serial No:
Stainless Steel Vapor Chamber-575 Gallon. Inside straight-wall dimensions: 4 ft. dia. x 6 ft. 2 in. H. Manway diameter: 1 ft. 4 in. Inlets: (1) 1 ft. 4 in. L x 1 ft. 4 in. H liquid infeed port, (1) 5 in. dia. port, (1) 3/4 in. dia. port. Outlets: (1) 20 in. dia. vapor discharge port, (1) 8 in. dia. drain port, (1) 1-1/2 in. dia. NPT port, (1) 3 in. dia. S-line fitting. Overall dimensions: 5 ft. 5 in. L x 4 ft. 7 in. W x 16 ft. 1 in. H.(HB2).

Click here for more information (340.7 KB)

Click On Picture

C.E. Rogers Vacuum Pan Evaporator - 35 Gallons

C.E. Rogers Vacuum Pan Evaporator - 35 Gallons
Mfg: C.E. Rogers Model:
Stock No: OI224. Serial No: 17635 69
C.E. Rogers Vacuum Pan Evaporator - 35 Gallons. S/N: 17635 69. (2) 5 in. dia. sight glasses. Access to tank is provided by a 30-1/2 in. wide, 4-step stairway with side rails. Inlets/outlets: (1) 3 in. dia. bevel, (2) in. FNPT, (2) 1 in. FNPT, (2) 1 in. MNPT. Overall dimensions: 6 ft. L x 3 ft. W x 8 ft. 5 in. H.

Click here for operating instructions (365.9 KB)
Click here for more information (384.6 KB)

Click On Picture

Cherry Burrell Stainless Steel Vacuumizer- 140 Gallon

Cherry Burrell Stainless Steel Vacuumizer- 140 Gallon
Mfg: Cherry-Burrell Model:
Stock No: 136 Serial No:
Cherry Burrell Stainless Steel Vacuumizer- 140 Gallons. Designed for HTST use. MAWP: 500 psi. 17-1/2 in. dia. manway. Taylor Electronic transmitter. Equipped with a 3-1/2 in. dia. and a 5 in. dia. sight glass. Leg height: 62 in. Inlets: (1) 6 in. dia. S-line. Outlets: (1) 4 in. dia. S-Line discharge, (1) 2 in. dia. S-Line. Overall dimensions: 47-1/2 in. L x 42 in. W x 106 in. H.

Click here for more information (208.4 KB)

Click On Picture

Crepaco Stainless Steel Deaerator- 250 Gallon

Crepaco Stainless Steel Deaerator- 250 Gallon
Mfg: Crepaco Model:
Stock No: 4R-177.0 Serial No: VH 751
Crepaco Stainless Steel Deaerator- 250 Gallon. S/N: VH 751. Inside straight-wall dimensions: 3 ft. dia. x 5 ft. H. Manway diameter: 1 ft. 8 in. Inlets: (1) 2 in. dia. S-line, (1) 3 in. dia. S-line, (1) 4 in. dia. S-line. Outlets: (1) 6 in. dia. port. Overall dimensions: 4 ft. 2 in. L x 3 ft. 7 in. W x 9 ft. 9-1/2 in. H.

Click here for more information (298.4 KB)

Click On Picture

Cherry Burrell Flavorizer ARO-VAC Model AVA-SC

Cherry Burrell Flavorizer ARO-VAC Model AVA-SC
Mfg: Cherry-Burrell Model: AVA-SC
Stock No: SACH076.1 Serial No: 321
Cherry Burrell Stainless Steel Flavorizer ARO-VAC. Model AVA-SC. S/N 321. (1) 2 in. bottom drain, (1) 1-½ in. top inlet, (1) 2-½ in. top side inlet. Tank dimensions 14-½ in. Diameter, 38 in. Depth.

Click here for more information (190.9 KB)

Click On Picture

Stainless Steel Single Shell Condenser Tubes

Stainless Steel Single Shell Condenser Tubes
Mfg: Not Specified Model:
Stock No: SFF265B. Serial No:
(3) Stainless Steel Single Shell Condenser Tubes. Stainless steel construction. Tube 1: 7-3/4 in. inner diameter x 52 in. L. Shell thickness: .080 in. Inlets: (1) 1-1/2 in. inlet. Outlets: (1) 1-1/2 in. outlet. Tube 2: 7-3/4 in. inner diameter x 94-1/2 in. L. Shell thickness: .080 in. Inlets: (1) 1-1/2 in. inlet. Outlets: (1) 1-1/2 in. outlet. Tube 3: 9-3/4 in. inner diameter x 90-1/2 in. L. Shell thickness: .080 in. Inlets: (1) 1-1/2 in. inlet. Outlets: (1) 1-1/2 in. outlet. Overall dimensions: 107 in. L x 46 in. W x 18 in. H.

Click here for more information (247.1 KB)

Click On Picture

Electron Machine Corp. Microprocessor Refractometer Sensing Head

Electron Machine Corp. Microprocessor Refractometer Sensing Head
Mfg: Electron Machine Corp. Model: MPR-83 / MPR-83R
Stock No: ARSU001.15 Serial No: 7090
Electron Machine Corp. Microprocessor Refractometer Sensing Head. Model: MPR-83 / MPR-83R. This sensing head fits the MPR-83 series of microprocessor refractometers that are typically used to measure the refractive indexes of process fluids. Microprocessor refractometers may also be used as error indicators or as part of complete process control systems and can be inserted directly into process lines or vessels for measurements and controls. Sample of applications include: fructose, glycol, NaOH, black and weak liquors, and coatings. Inlets/outlets: (2) 1-1/2 in. dia. S-line fittings. Overall dimensions: 12 in. L x 7-1/2 in. W x 13-1/2 in. H.(ACN80).

Click here for more information (297.2 KB)
Click here for more information (202.8 KB)

Click On Picture

Fisher Butterfly Control Valve

Fisher Butterfly Control Valve
Mfg: Fisher Model:
Stock No: 2500.pf1aC Serial No: BF271327, BF271326
(2) Fisher Butterfly Control Valve. Type: 9510. Size: 12 in. Body style: flangeless. ANSI Class: 125. Body rating: 175 PSI. Differential: 50 PSID. Body material: A 126 CLB. Valve rotation: 90 . Actuator size: 60. Spring range: 3.7 to 13.1. Actuator connection: in. NPT Diaphragm material: nitrile. Inlets/Outlets: (2) 12 in. Port. Overall Dimensions: 2 ft. 11 in. L x 1 ft. 6 in. W x 4 ft. 1 in. H.(H12)(ACN187)

Click here for more information (290.1 KB)

Click On Picture

APV Plate Evaporator Plates

APV Plate Evaporator Plates
Mfg: APV Model:
Stock No: RAAF070. Serial No:
(106) APV Plate Evaporator Plates. Inlets: (1) 6 in. L x 2 in. W (product), (2) 2 in. L x 1 in. W, (2) 14 in. L x 4 in. W (media). Outlets: (2) 21 in. L x 10-1/2 in W (vapor). Plate dimensions: 54 in. L x 29-1/2 in. W.(H13).

Click here for more information (282.0 KB)

Click On Picture

The Electron Machine Corp. Microprocessor Refractometer Unit Sensing Head

The Electron Machine Corp. Microprocessor Refractometer Unit Sensing Head
Mfg: The Electron Machine Corp. Model: MPR-83/MPR-83R
Stock No: RCCB301A.13 Serial No:
The Electron Machine Corp. Microprocessor Refractometer Unit Sensing Head. Model MPR-83 / MPR-83R. This sensing head fits the MPR-83 series of microprocessor refractometers that are typically used to measure the refractive indexes of process fluids. Microprocessor refractometers may also be used as error indicators or as part of complete process control systems and can be inserted directly into process lines or vessels for measurements and controls. Sample of applications include: fructose, glycol, NaOH, black and weak liquors, and coatings. (ACN60).

Click here for more information (142.1 KB)

Click On Picture

Cleaver Brooks Spraymaster Deaerator- 800 Gallons

Cleaver Brooks Spraymaster Deaerator- 800 Gallons
Mfg: Cleaver Brooks Model: SM30
Stock No: HD-SC294.16a Serial No: DS-3660
Cleaver Brooks Spraymaster Deaerator- 800 Gallons. Model: SM30. S/N: DS-3660. Nat'l Bd: 53121. MAWP: 50 psi @ 650 F. Shell thickness: 0.250 in. Head thickness: 0.312 in. (2) Pressure relief valves. Oval manway: 15 in. L x 11 in. W. Tank dimensions: 103 in. L x 48 in. dia. (2) Centriflo pumps, Type 618-D8-F, capacity: 120 gpm (each). US Motor, 25 hp, 3520 rpm, 230/460 V, 62.0/31.0 amps, 60 Hz, 3 phase. Leeson Motor, 25 hp, 3500 rpm, 208-230/460 V, 64-62/31 amps. Inlets/outlets: (2) 2-1/2 in., (2) 1/2 in., (1) 5 in., (3) 2 in. Overall dimensions: 11 ft. 6 in. L x 54 in. W x 80 in. H.(HB2)(ACN320).

Click here for more information (159.0 KB)

Click On Picture

Rising Film Colandria

Rising Film Colandria
Mfg: Not Specified Model:
Stock No: 165 Serial No:
Rising Film Colandria. 54 hole 3 in. inlet, 163 in. Long x 26 in. diameter.

Click On Picture

American Optical Leica Mark II Series AO ABBE Digital Refractometer

American Optical Leica Mark II Series AO ABBE Digital Refractometer
Mfg: American Optical Model: 10450
Stock No: HDYA188.3 Serial No: 08780581
American Optical Leica Mark II AO ABBE Digital Refractometer. Model: 10450. S/N: 08780581. Power supply: 117 VAC, 50-60 Hz, 25 watts. This digital model makes it easy to take index of refraction measurements. Simply place your sample on the prism, adjust the shadow line (if using the uncorrected scale), focus the image, and press the READ button to see your results on the bright LED display. Overall dimensions: 1 ft. 2 in. L x 7 in. W x 1 ft. 2-1/2 in. H.

Click here for more information (86.8 KB)

Click On Picture

Stainless Steel Vapor Tubing

Stainless Steel Vapor Tubing
Mfg: Not Specified Model:
Stock No: GKFC24 Serial No:
Stainless Steel Vapor Tubing

Click On Picture

Stainless Steel Vapor Tubing Elbows

Stainless Steel Vapor Tubing Elbows
Mfg: Not Specified Model:
Stock No: GKFC25 Serial No:
Stainless Steel Vapor Tubing Elbows



View previously sold Evaporator Miscellaneous. Genemco can source products required for your project.

Click Here if you don't see what you're looking for in our online catalog.


Other Equipment:Single and Multiple Effect Evaporators | HTST Pasteurizer Systems | Plate Heat Exchangers | Mycom Compressors | Evaporative Condensers 
Other Categories:Ammonia Refrigeration | Evaporator Coils | Freon Evaporators | Freon Air Cooled Condenser | Dicers / Slicers 
Other Manufacturers:Freon Condensing Units | Sealers | Case Packers | Porcupine Dryer | Comfort Heating/Cooling 

 Genemco Sells Used Plate Heat Exchanger/Evaporator, Vacuum Pan Evaporator, Lo-Temp Evaporators and Vacuumizer Tanks.