|
Click On Picture
|
Stainless Steel Tank - 250 gallons
|
Mfg: Not Specified
|
Model:
|
Stock No: TASP155
|
Serial No:
|
S.S. Tank, 46" Dia, Steep Slope Discharge, One Side is 14" Tall, One Side is 60" Tall, Covered Top. Estimated capacity: 250 gallons.
|
|
|
Click On Picture
|
APV R3 Rectangular Inlet Positive Displacement Pump
|
Mfg: APV
|
Model: R3-RI
|
Stock No: SCJC218.3
|
Serial No:
|
APV R3 Positive Displacement Pump on cart with hopper infeed. Pump nameplate missing. Rectangular inlet: 2 in. x 4 in. Outlet: 2 in. Tri-Clamp. 5-lobe rubber impellers. Sterling electric motor: 0.75 HP, 220/440V, 2.4/1.2 amp, 60 Hz, 3-phase.
|
|
|
Click On Picture
|
Steel Feeder/Hopper – 145 cubic ft.
|
Mfg: Not Specified
|
Model:
|
Stock No: MRSP120
|
Serial No:
|
Steel Feeder/Hopper – 145 cubic ft. capacity, w/ approximately 15 ft. stand. Equipped with: (1) motor driven slide gate, (1) model: R, Roto-Bin-Dicator® for level sensing. Dayton gear motor, 1/6 hp, 40 rpm, 115 V, 4.9 amps, 60 Hz, single phase. Gear ratio: 42.7:1. Final rpm: 1. Torque: 225 in-lbs. (1) 3 ft. L x 1 ft. 5 in. W top access door. Inlet: (1) 10 in. L x 10 in. W port, (1) 5 in. dia. port. Outlet: (1) 8 in. L x 8 in. W port. Overall dimensions: 5 ft. 11 in. L x 5 ft. 7 in. W x 15 ft. 4 in. H. (BH).
|
Click here for more information (479.2 KB)
|
|
Click On Picture
|
Steel Feeder/Hopper - 145 Cubic ft.
|
Mfg: Not Specified
|
Model:
|
Stock No: MRSP121
|
Serial No:
|
Steel Feeder/Hopper – 145 cubic ft. capacity, w/ approximately 15 ft. stand. Equipped with: (1) pneumatic piston activated Plattco slidegate, model: UUS08852, (1) model: R, Roto-Bin-Dicator® for level sensing. (1) 3 ft. 2 in L x 1 ft. 9 in. W top access door. Inlet: (1) 10 in. L x 10 in. W port. Outlet: (1) 8 in. L x 8 in. W port. Overall dimensions: 5 ft. 10 in. L x 5 ft. 6 in. W x 15 ft. 4 in. H. (H17).
|
Click here for more information (404.5 KB)
|
|
Click On Picture
|
APV Stainless Steel Feeding Hopper Tank and Pump Package-360 gallons
|
Mfg: APV
|
Model:
|
Stock No: RBFM823.20
|
Serial No:
|
(2) APV Stainless Steel Feeding Hopper Tank and Pump Package-360 gallons. Pump Model: R6R1. S/N: 20898. 2nd Pump Model: R4R. S/N: R-8734-048S. Inside straight wall dimensions: 6 ft. L x 2 ft. 11 in. W x 44 in. H. Inlets: (1) 6 ft. x 2 ft. 11 in. W (infeed hopper), (2) 9 in. L x 3 in. W. (pump inlets). Outlets: (2) 1-1/2 in. dia. ACME fittings, (2) 3 in. dia. ACME fittings. Overall dimensions: 6 ft. 3 in. L x 3 ft. 2 in. W x 5 ft. 2 in. H.
|
Click here for more information (179.7 KB)
|
|
Click On Picture
|
1994 Cozzini Vacuum Chamber Processor with Pump – 185 Gallons
|
Mfg: Cozzini
|
Model: VP-700
|
Stock No: KAAM0418.13
|
Serial No: 0128
|
1994 Cozzini Vacuum Chamber Processor with Pump. Model: VP-700. Approximate throughput capacity: 11,000 lbs. per hour. Approximate vacuum chamber capacity: 185 gallons. Tri-Clover positive displacement pump. Reliance electric motor, 7-1/2 hp, 1755 rpm, 230/460 V, 27/13.5 amps, 60 Hz, 3 phase. Reliance electric variable speed module, rpm (min/max): 450/45. Typically used in the processing of meat emulsions such as wieners and hot dogs, the Cozzini VP-700 removes air from the product prior to packaging, thus ensuring product uniformity and increasing shelf life. Inlets: (1) 3/8 in. dia. FNPT, (1) 3/4 in. dia. FNPT ball valve, (1) 2 in. dia. FNPT, (1) 2 in. dia. S-line fitting, (2) 4 in. dia. S-line fitting. Outlets: (1) 9 in. L x 2-1/2 in. W discharge. Overall dimensions: 7 ft. 8 in. L x 4 ft. 8 in. W x 7 ft. 4 in. H.(ACN400).
|
Click here for more information (848.9 KB)
|
|
Click On Picture
|
APV Crepaco Stainless Steel Holding Tank and Pump – 300 Gallons
|
Mfg: Crepaco
|
Model: M.H.
|
Stock No: KAAM0219.7a
|
Serial No: C-0611
|
APV Crepaco Stainless Steel Holding Tank and Pump – 300 Gallons. Model: M.H. S/N: C-0611. Infeed hopper diameter: 6 ft. Hopper wall thickness: 0.118 inches. APV Crepaco Positive Displacement Pump with Baldor Industrial Motor, 15 hp, 1760 rpm, 208-230/460 V, 40-37/18.5 amps, 60 Hz, 3 phase. Motor drive. Inlets: (1) 9 in. L x 6-1/2 in. W infeed. Outlets: (1) 4 in. dia. discharge ACME fitting. Overall dimensions: 7 ft. 11 ft. L x 6 ft. 1 in. W x 7 ft. 9 in. H.
|
Click here for more information (497.9 KB)
|
|
Click On Picture
|
General Mills Stainless Steel Tank/Hopper- 2500 Gallon
|
Mfg: General Mills
|
Model:
|
Stock No: SGMI250.31
|
Serial No: 1057099
|
General Mills Stainless Steel Tank/Hopper- 2500 Gallon. S/N: 01057099. Inlets: (1) 1-1/2 in. dia. S-line, (1) 2-1/2 in. dia. pipe, (1) 3 in. dia. threaded fitting, (2) 19-1/2 in. diameter clamp ports. Outlets: (1) 43 in. dia. outlet with a 50 in. dia. flange and (8) 5/8 in. dia. attachment holes at a center-to-center distance of 46 in. Overall dimensions: 91 in. dia. x 18 ft. 4 in. H.
|
Click here for more information (201.8 KB)
|
|
Click On Picture
|
1996 K-Tron Soder Weigh Belt Mechanical Feeder
|
Mfg: K-Tron Soder
|
Model: W300
|
Stock No: SMBV101.
|
Serial No:
|
1996 K-Tron Soder Weigh Belt Mechanical Feeder. Approximate capacity: 5000 lbs/hr. Material of construction: stainless steel. Conveyor belt width: 10-1/2 in. Leeson motor, 1/2 hp, 1750 rpm, 180 V, 2.5 amps. SM-Cyclo gear drive, chain driven, ratio: 29, final rpm: 60.3, torque: 870 in.-lb. The weigh belt feeder offers continuous and gravimetric feeding of bulk materials or can be used for batch feeding or the metering of a bulk material flow. Interface modules are available for installations with computer systems. Inlets (1) 14-1/2 in. dia. Infeed hopper with an 8 in. adjustable open/close tray. Outlets: (1) 15 in. x 6 in. primary outlet, 15 in. x 3-1/4 in. secondary outlet, both with handle to select which outlet will be used. (1) 11 in. x 12-1/2in. overflow outlet with tray to dispense substance or to allow to accumulate then dispense. Overall dimensions: 4 ft. 5 in. L x 2 ft. 6 in. W x 5 ft. 9 in. H.(H11)(ACN300).
|
Click here for specifications (57.1 KB) Click here for more information (408.2 KB)
|
|
Click On Picture
|
1992 FMC Syntron Cone Vibratory Shaker
|
Mfg: FMC Technologies (JBT FoodTech)
|
Model:
|
Stock No: CCFP505.
|
Serial No:
|
1992 FMC Syntron Cone Vibratory Shaker. Shaker features a 31 in. dia. x 45 in. H. conical hopper with attached lid. Product exits through a 28 in. L x 10 in. W x 4 in. H. chute. Inlets/outlets: (1) 8 in. dia. central inlet, and (1) 6-1/2 in. dia. central outlet. Syntron Magnetic Vibrator Motor, Model: V-20. S/N EE11822115 V, 2.0 amps, 60 Hz. Syntron Magnetic Feeder, Model: F-152 A. S/N: L69952115 V, 2.5 amps, 60 Hz. Equipment is frame-mounted. Overall dimensions: 36 in. L x 31 in. W x 61 in. H.
|
Click here for more information (220.7 KB)
|
|
Click On Picture
|
Fedco Stainless Steel Topping Applicator
|
Mfg: Fedco Engineering Systems
|
Model:
|
Stock No: HDNP210C.6
|
Serial No:
|
Fedco Stainless Steel Topping Applicator. Has two agitators with drives. Hopper/agitator assembles slide length wide on track. Hopper dimensions (inside) 12 in. W, 32 in. L, 18 in. H. (Curved bottom). Has two on/off switches, on for each drive. Upper agitator switch runs straight to the motor. Lower agitator switch runs to Allen Bradley control drive, then to the motor. Control Drive: Bulleting 1333 Adjustable frequency AC Motor Drive. Allen Bradley, Cat No. 1333-AAB, Ser: B, S/N B17355, Input (3 phase) 460 volt, 50/60 Hz, 2.6 KVA, 3.3 amps. Output (3 phase): 460 volt, 60 Hz, 1.7 KVA, 2.1 amps. Dimensions of frame: 38 in. W, 85-½ in. L, 35 in. H. Overall dimensions: 38 in. W, 85-½ in. L, 51-½ in. H.
|
Click here for more information (227.1 KB)
|
|
Click On Picture
|
Pick Up Hopper with Stand-15 Gallon
|
Mfg: Not Specified
|
Model:
|
Stock No: SGMI266.
|
Serial No:
|
Pick Up Hopper with Stand-15 Gallon. Inlets: (1) 7 in. dia. flange with (8) 7/8 in. dia. Mounting holes at a center to center 4 in. adjacent and a center to center of 10-1/2 in. opposite. (1) 1-1/2 in. s-line input. Outlets: (4) 2 in. dia. S-line fittings. Overall dimensions: 2 ft. 4-7/8 in. L. x 1 ft. 10-1/2 in. W. x 3 ft. 2 in. H.
|
Click here for more information (135.7 KB)
|
|
Click On Picture
|
Stainless Steel Powder Silo with Airlock
|
Mfg: Shick
|
Model:
|
Stock No: HDAF901.14
|
Serial No:
|
Shick Tube-Veyor Scale and Receiving Hopper- 40 Cu. Ft. Mat'l constr: ASTM A240 304 stainless steel. Rotary Airlock Valve with U.S. Motor, 3/4 hp, 1750 rpm, 230/460 V, 3.6/1.8 amps, 60 Hz, 3 phase and a Torqube Drive, ratio: 60.1, torque: 1190, final rpm: 29. (3) legs. Scaling and receiving hoppers are used in pressure, vacuum and gravity scaling and receiving applications. Inlets: (3) 4 in. dia. ports. Outlets: (2) 4-1/2 in. dia. discharge. 17 in. L x 18-1/2 L manway. Overall dimensions: 50 in. L x 50 in. W x 10 ft. 6 in. H.(HB1).
|
Click here for more information (215.9 KB)
|
|
Click On Picture
|
Pick-Up Hopper- 25 Gallon
|
Mfg: Not Specified
|
Model:
|
Stock No: SNPM138.a
|
Serial No:
|
Pick-Up Hopper- 25 Gallon. 3-Leg support. Filtration capability. Inlets: (1) 10 in. dia. infeed port. Outlets: (1) 2-1/2 in. dia. discharge port. Overall dimensions: 34 in. L x 27 in. W x 51-1/2 in. H.
|
Click here for more information (161.5 KB)
|
|
Click On Picture
|
Pick-Up Hopper- 25 Gallon
|
Mfg: Not Specified
|
Model:
|
Stock No: SNPM140.a
|
Serial No:
|
Pick-Up Hopper- 25 Gallon. 3-Leg support. Filtration capability. Inlets: (1) 10 in. dia. infeed port. Outlets: (1) 2-1/2 in. dia. discharge port. Overall dimensions: 34 in. L x 27 in. W x 51-1/2 in. H.
|
Click here for more information (186.9 KB)
|
|
Click On Picture
|
Pick-Up Hopper- 25 Gallon
|
Mfg: Not Specified
|
Model:
|
Stock No: SNPM139.a
|
Serial No:
|
Pick-Up Hopper- 25 Gallon. 3-Leg support. Filtration capability. Inlets: (1) 10 in. dia. infeed port. Outlets: (1) 2-1/2 in. dia. discharge port. Overall dimensions: 34 in. L x 27 in. W x 51-1/2 in. H.
|
Click here for more information (166.7 KB)
|
|
Click On Picture
|
Stainless Steel Hopper with Rotary Airlock
|
Mfg: Not Specified
|
Model:
|
Stock No: HDBV072.4
|
Serial No:
|
Stainless Steel Hopper with Rotary Airlock. Infeed hopper dimensions: 36 in. L x 36 in. W. Hopper uses a 36 in. L x 36 in. W guard. (2) Syntron Electric Vibrators, Model: V-20, S/N's: C-12708 and C-12935, electrical requirements: 115 V, 2.0 amps, 60 Hz. Baldor Industrial Motor, 1/2 hp, 1725 rpm, 115-208/230 V, 60 Hz. Reliance Electric Tigear 150 Gear Reducer, 20 ratio, 86.25 rpm (final). Inlets: (4) 1-1/2 in. dia. S-line fittings, (3) 6 in. dia. feed ports, (1) 8 in. dia. infeed (airlock). Outlets: (2) 2 in. dia. S-line fittings. Overall dimensions: 39-1/2 in. L x 39-1/2 in. W x 60 in. H.
|
Click here for more information (315.2 KB)
|
|
Click On Picture
|
2003 AZO Stainless Steel Vibrating Hopper
|
Mfg: AZO
|
Model: 1100
|
Stock No: SGMI012.
|
Serial No:
|
2003 AZO Stainless Steel Vibrating Hopper. Model: 1100. Type: 402580. Machine number: 043386A-1-023930-00. Feed hopper dimensions: 44 in. diameter x 18 in. H. Cone spreader: 34 in. diameter x 12 in. H. CE Vibrating Motor, Type: JV134-63, 1.07 hp, 1730 rpm, 460 V, 1.65 amps, 60 Hz. Overall dimensions: 62 in. L x 50 in. W x 19 in. H.
|
Click here for more information (168.4 KB)
|
|
Click On Picture
|
Stainless Steel Feed Hopper-430 gallon
|
Mfg: Not Specified
|
Model:
|
Stock No: RBFM1005.6
|
Serial No:
|
Stainless Steel Feed Hopper-430 gallon. Inside straight wall dimensions: 48 in. L x 48 in. W x 52 in. H. Inlets: (1) 4 ft. x 4 ft. (hopper infeed). Hydraulically Driven Rotary Pump is missing rotors and cover. Outlets: (1) 9-1/2 in. L x 6-1/2 in. port (bottom discharge). Overall dimensions: 5 ft. L x 4 ft. 2 in. W x 6 ft. H.
|
Click here for more information (150.7 KB)
|
|
Click On Picture
|
Stainless Steel Ice Hopper and Auger
|
Mfg: Not Specified
|
Model:
|
Stock No: EKTF7260B.2
|
Serial No:
|
Stainless Steel Ice Hopper and Auger. Baldor motor. Boston motor drive. Capacity: 100 gallon. (3) Screws: 6 in. diameter x 53 in. L. (2) Sight glasses: 10 in. L x 4 in. W. Lid opening: 21-1/2 in. L x 12-1/4 in. W. Inlet: 21 in. L x 10 in. W. Outlet: 12 in. L x 12 in. W. Overall dimensions: 92 in. L x 31 in. W x 54 in. H.
|
Click here for more information (269.7 KB)
|
|
Click On Picture
|
D&F Poultry Ice Hopper and Auger
|
Mfg: D&F
|
Model:
|
Stock No: EKTF7260.2
|
Serial No:
|
D&F Poultry Ice Hopper and Auger. Baldor motor, 1 hp, 1725 rpm, 208-230/460 V, 3.6-3.4/1.7 amps, 60 Hz, 3 phase. Flexaline motor drive, 60 ratio, maximum input: 0.9 hp, rating: 1750 rpm, output: 28.75 rpm. Stainless steel body. Container capacity: 120 gallon. (3) Screws: 6 in. diameter x 47 in. L. Inlet: 20 in. L x 20 in. W. Outlet: 14 in. L x 12 in. W. Overall dimensions: 81 in. L x 29 in. W x 58 in. H. (ACN85)
|
Click here for more information (141.6 KB)
|
|
Click On Picture
|
Young Industries Hopper with Mixer
|
Mfg: Young Industries
|
Model:
|
Stock No: PMI87a.1
|
Serial No: FBD-528
|
Young Industries Hopper with Mixer. S/N: FBD-528. Shop No: 7581. Cust. No: 18407. Infeed hopper dimensions: 44 in. L x 29 in. W. Unit is equipped with 5-1/2 in. long x 1-1/2 in. wide, 3-blade propeller. (8) 5 in. ports. Baldor Electric Motor. 1/3 hp, 1725 rpm, 208-230/460 V, 60 Hz, 1.8-1.6/0.8 amps, 3 phase. Boston motor, ratio: 5, 345 rpm (final). Inlets: (1) 30 in. L x 29 in. W infeed, (1) 3 in. port, (1) 7 in. port infeed. Outlet: (1) 3-1/2 in. discharge port. Overall dimensions: 60 in. L x 54 in. W x 67 in. H.
|
Click here for more information (253.4 KB)
|
|
View previously sold Hopper Feeders. Genemco can source products required for your project.
|
|
|